有部分人总会问为什么LED全彩显示屏配电箱频繁跳闸？下面LED全彩显示屏就对LED全彩显示屏频繁跳闸做一个简单的分析。希望能解决您LED全彩显示屏配电箱跳闸的疑惑。

      一般LED全彩显示屏配电箱频繁跳闸有四点因素：漏电保护器***不合理、在保护范围内没有形成有效的二级或***漏电保护、漏电保护器本身有一定的局限性(三相电用电不平衡)、漏电保护器选型不合理等等。

1、漏电保护器不合理

      由于LED全彩显示屏安装现场所具有的特殊性以及漏电保护器本身不可避免的误动和拒动，再加上没有按照实际用电情况对漏电保护器进行布置，造成了总漏电保护器频繁跳闸。

LED显示屏解决方案：这种情况除了加强管理外，还需要从技术的角度，根据实际情况对漏电保护器进行合理布置。

2、在保护范围内没有形成有效的二级或漏电保护

      开关箱内的末级漏电保护器是用电设备的主保护，由于LED全彩显示屏内金属导体很多，电线接头较多，如果导线绝缘不是很好，就会导致经常漏电的状况；有的还加了一些插座，在很多时候都不装漏电保护器，经常造成漏电。

LED显示屏解决方案：只有在每个保护范围内形成有效的二级或***漏电保护模式，才能有效地减少漏电保护器的频繁跳闸。

3、漏电保护器本身有一定的局限性(三相电用电不平衡)

      目前的漏电保护器，不论是电磁型还是电子型均采用磁感应电压互感器拾取用电设备主回路中的漏电流，三相或三相四线在磁环中不可能布置完全均衡。LED全彩显示屏的三相用电负荷也不可能完全平衡，在大电流下或较高的过电压下，会在有很高导磁率的磁环中感应出一定的电动势，这个电动势大到一定程度，就会导致漏电保护器跳闸。

4、漏电保护器选型不合理

      开关箱内使用的额(e)(e)定漏电动作电流超过了30mA或者是超过用电设备额(e)(e)定电流两倍以上的漏电保护器，或是选用了带延时型的漏电保护器，由于额(e)(e)定漏电动作电流的提高或保护灵敏(min)度的下降，发生漏电故障时，末级漏电保护器没有动作，上级漏电保护器就可能动作。

LED显示屏解决方案：在给下面LED全彩显示屏通电时的启动电流往往都比较大，此大电流可能会使漏电保护器跳闸。因此，应尽可能分批次地给显示屏的箱体上电。另外，一般应选用对浪涌过电压、过电流不太敏感的电磁型漏电保护器；或选用比额(e)定电流大1.5~2倍的电子式漏电保护器，但作为末级漏电保护，额(e)定漏电动作电流不应大于30mA。